Build your repeater hub

Configure your hub

Based on Proeye's standard hub reference designs. Final equipment, carrier allocation and power capacity are confirmed by a site survey and design.

Closest buildGold repeater hubView hub

1 Which carriers need coverage?

Each carrier uses its own CEL-FI G41 repeater module.

Telstra Optus Vodafone

2 How should the system be looked after?

Fully remote managedModem, remote power cycling and monitored backup power. Most faults and upgrades handled remotely. On-site serviced, battery backedBackup battery and fuse board. Firmware, changes and checks done by a technician on site. Basic enclosureIndividual DC supplies for each module. Lowest build cost, serviced on site.

3 Choose the cabinet

Ventilated dual-lock cabinetHills Home Hub cabinet with top and bottom vents and dual key locks. Viewing-window cabinetB&R HDC20 vented cabinet with a window door to check indicator lights without opening it. Remote managed builds only.

4 How many hubs on site?

Larger buildings may need a hub for each coverage zone.

One hub Two hubs Three or more

5 About your site

Building type

Approximate floor area (optional)

Where is reception poor?

Whole building Basement or car park Lifts Back of house Trading or public areas Upper levels

Suburb and state (optional)

Timeframe (optional)

6 Send your configuration to Proeye

This is a preliminary configuration. The hub type, equipment, carrier allocation and battery capacity are confirmed by technical assessment, a site survey and engineering design before we quote.

Configuration summary

Quote request form

Opens our Jotform quote form in a new tab with this configuration already filled in under "Any other comments". Add your contact details, site details and floor plans there.

Continue to the quote form

Email

Opens a draft email to enquiries@proeyesecurity.com.au with the configuration. Nothing is sent until you press send.

Your hub

Closest standard buildGold repeater hub

Platinum hub, door open. Vented cabinet with a window door so status lights can be checked without opening it. — Platinum hubs installed at a residential aged care community in Victoria. Site labels and serial numbers have been removed.

Inside a Platinum hub. IP relay for remote power cycling, fuse board, monitored power supply, backup battery and network switch beneath a G41 module. — Platinum hubs installed at a residential aged care community in Victoria. Site labels and serial numbers have been removed.

Repeater hub in service. A wall-mounted Proeye repeater hub with modules, relay, power supply and backup battery. — Gold hubs built for a new retail development in Victoria, with the mains outlet at the top of the cabinet.

CEL-FI G41 modules. Repeater modules inside a Proeye hub, ready for configuration. — Gold hubs built for a new retail development in Victoria, with the mains outlet at the top of the cabinet.

Cabinet: Hills 24HH1000 ventilated cabinet
Repeater modules: 3 × CEL-FI G41
Hubs on site: 1

Included in each hub

Servicing

An indicative configuration based on Proeye's August 2025 hub reference designs. Equipment, carrier allocation, battery capacity and remote services are confirmed in your quotation.

How remote management works

A fully managed Proeye hub is reached through three platforms, each doing one job.

IoT platform. Manages the SIM that gives the hub its own cellular connection.
Proeye private network. Secure, independent access to the repeater modules and the power relay, so modules can be power-cycled remotely.
CEL-FI WAVE portal. Higher-level repeater management: firmware, configuration, security lock, performance and alarms.

Firmware can be upgraded remotely as networks evolve from 4G to 5G, and supply and battery condition can be monitored where a monitored supply is fitted.

Built and tested before it reaches site

Every Proeye hub is assembled on the bench, tested and updated to the latest repeater firmware before installation.

That means less time on site, tidier installations and a known-good system from day one. See the hubs in place on our projects.

See a hub project Compare standard hub builds

Hubs built and tested on the bench. Repeater hubs assembled and tested before delivery to site.